Pro Tools TDM 6.4.1cs4 Update

For Pro Tools|24 MIX Systems With Pro Tools 6.4.1 on Windows XP


Index of All Pro Tools CS Updates

July 21, 2005

Will not work without Pro Tools TDM 6.4.1 for Pro Tools|24 MIX systems already installed.

Pro Tools TDM 6.4.1cs4 Update

For Pro Tools|24 MIX Systems with Pro Tools TDM 6.4.1 for Windows XP

From the Included Pro Tools TDM 6.4.1cs4 Read Me document:

What's Fixed in Pro Tools TDM 6.4.1cs4?

Pro Tools TDM 6.4.1cs4 for Windows XP contains the following:

Fixed: Levels in the Pro Tools mixer could vary by 12dB when interfaces were connected to more than one MIX card (Items # 58105 and 58299)

  • In order to fix these problems, +6 dB fader gain mode has been disabled in Pro Tools 6.4.1cs4, which will now only operate in +12 dB fader gain mode. Please note the following —
    • Any +6 dB or pre-Pro Tools 6.4 session opened in Pro Tools TDM 6.4.1cs4 will play at the correct levels.
    • Volume level compatibility with pre-Pro Tools 6.4 versions of Pro Tools is maintained for all volume levels below +6 dB.
    • Any volume levels written above +6 in a +12 dB session will play properly in Pro Tools 6.4 or later. Volume data written above +6 dB will be truncated (moved to +6 dB) if the session is opened on a pre-6.4 version of Pro Tools This is the same behavior as all versions of Pro Tools 6.4 and later.
    • You may still "Save Session Copy in…" as a +6 dB session, with the same truncation behavior, as with all versions of Pro Tools from 6.4-> 6.9.x. The result will be no different than just opening the session in a pre-Pro Tools 6.4 system.

Fixed: Scrubbing or Shuttling a 9-Pin Device Did Not Smoothly Update the 9-Pin Device (Item #51198)

  • When using either the control surface jog wheel or the “Shuttle” Numeric Keypad Mode, 9-pin devices would start and stop during shuttle and scrub operations.

Includes fixes from Pro Tools TDM 6.4.1cs3:

Fixed: Launching or Creating a Session with More Than 16 Mono Bus or Output Paths May Result in a Crash (Item #57053)

  • This crash would only occur when all active bus paths were mono (no stereo paths or mono sub-paths) and a Surround Mixer plug-in was installed.

Includes fixes from Pro Tools TDM 6.4.1cs2:

Fixed: Inconsistent Automation Playback and Audio Distortion (Item # 56215)

  • Using a surround mixer in certain configurations would cause inconsistent automation playback and/or audio distortion and corrupted preferences.

Includes fixes from Pro Tools TDM 6.4.1cs1:

Fixed: When Using Pro Tools in +12 dB Fader Gain Mode, the Level on Outputs Could Be Incorrectly Increased by Up to18 dB (Item #54461)

  • Creating a large session where the mixer is spread out over multiple DSPs could result in output levels increasing by up to 18 dB.

Fixed: Intermittent Pops or Incorrect Audio when Playing a Session (Item #54406)

  • When playing a session, occasional pops or random audio could be heard. The problem could be exacerbated by using a high Hardware Buffer setting.

Fixed: Potential Crash when Opening Sessions Containing Assigned MIDI Inputs or Outputs (Items #52092, 54498)

  • A crash occurs when opening some sessions with saved MIDI sources or destinations.

Fixed: When Importing or Browsing OMF Media That Referenced Certain SD II Files, Pro Tools Would Crash (Item #51931)

  • Pro Tools 6.4.1 crashes when importing an OMF or browsing OMF media containing SDII audio with a .OMF extension.

Fixed: Problems when Relinking SD II Media Containing a .omf Extension (Item #51955)

  • Pro Tools 6.4.1 fails to relink, or crashes when attempting to relink SD II audio with a .OMF extension.

Fixed: Sample-Rate Error Messages when Importing an OMF (Item #49709)

  • When importing certain OMFs, Pro Tools would display the error, "Could not create a new document because: an unexpected error happened while trying to determine the file’s audio sample rate." The prior workaround was to use DigiTranslator 1.x.

Who Should use Pro Tools TDM 6.4.1cs4?

This update is recommended for all Pro Tools|24 MIX users on Windows XP SP1 with Pro Tools TDM 6.4.1 and contains fixes in the following areas:

  • Scrubbing a 9 pin device with Pro Tools
  • Mixing or Recording
  • MIDI
  • Importing OMF sequences into Pro Tools
  • Relinking files with an .OMF extension

Important: Pro Tools TDM 6.4.1cs4 is provided as an interim "customer support (CS)" release to address the issues described. While our testing has not shown these changes to introduce other problems, this version has not been fully qualified by Digidesign.

Updating Pro Tools

To update to Pro Tools 6.4.1cs4:

  1. Verify Pro Tools TDM 6.4.1 is installed on your Pro Tools|24 MIX system.
  2. Quit the Pro Tools application if it is open.
  3. Locate the Pro Tools TDM 6.4.1cs4 installer and launch it.
  4. Follow the onscreen instructions to install Pro Tools 6.4.1cs4.
  5. When installation is complete, restart your computer.

If you have installed previous updates, some file versions may not change. This update installs the following files:

  • ProTools.exe (v6.4.1cs4)
  • Cfd.dll (v6.4.1cs4)
  • Surround Mixer.dpm (v6.4.1cs3)*
  • Surround Mixer.dpm.rsr (v6.4.1cs3)*
  • Surround Dithered Mixer.dpm (v6.4.1cs3)*
  • Surround Dithered Mixer.dpm.rsr (v6.4.1cs3)*
  • ProTools.rsr (v6.4.1cs1)
  • ProTools_chs.rsr (v6.4.1cs1)
  • ProTools_jpn.rsr (v6.4.1cs1)
  • ProTools_kor.rsr (v6.4.1cs1)
  • PT_Resource411.dll (v6.4.1cs1)
  • PT_Resource412.dll (v6.4.1cs1)
  • PT_Resource804.dll (v6.4.1cs1)
  • Cfd_Resource804 (v6.4.1cs1)
  • Cfd_Resource411 (v6.4.1cs1)
  • Cfd_Resource412 (v6.4.1cs1)
  • DAE.dll (v6.4.1cs1)
  • DAE.dll.rsr (v6.4.1cs1)
  • DAE_Resource804 (v6.4.1cs1)
  • DAE_Resource411 (v6.4.1cs1)
  • DAE_Resource412 (v6.4.1cs1)
  • File.dll (v6.4.1cs1)
  • File.dll.rsr (v6.4.1cs1)
  • File_Resource804 (v6.4.1cs1)
  • File_Resource411 (v6.4.1cs1)
  • File_Resource412 (v6.4.1cs1)

* Note that the standard non-dithered mixers will be installed to your plug-ins folder, and the dithered mixers will be installed to the "Plug-ins (unused)" folder. After installation, check Program Files\Common Files\Digidesign\DAE\Plug-Ins to verify you are running your chosen mixer type.

Download Instructions — Pro Tools TDM 6.4.1cs4 Update

For best results, use the latest version of Internet Explorer for Windows XP. Other browsers may not work properly with this download. This Pro Tools TDM 6.4.1cs4 Update requires a Pro Tools|24 MIX hardware system with Pro Tools TDM version 6.4.1 software already installed.

For Pro Tools|24 MIX Systems
with Pro Tools TDM 6.4.1 Software Only

For Windows XP Only
(includes support for Japanese, Korean and Chinese Simplified Operating Systems)

29.1 MB Windows ZIP file (.zip)

 

Download Help

  • If you experience download or decoding problems, see Download & Website Help
  • Windows ZIP (.zip) format downloads should be "Saved to Disk" first, rather than opened on the internet. These can be expanded on Windows XP systems by right-clicking on the downloaded files and choosing "Open".

More Information:

Digidesign Downloads | Digidesign Customer Service | Digidesign Technical Support